Will my factory-fitted charger work with TITAN?

Charger is fine for TITAN lithium - those voltages allow a 100% charge with no setting change.

Confirmed compatible. Will take a TITAN battery to a full 100% charge from solar input.

Fine to use when the internal DIP switch is set to position 'B' (middle). The TITAN BMS will prevent damage if the charger ever exceeds 14.4V.

Fine to use as is but note slow charging times due to 2.5A output for aux. battery charging. Pair with a solar or DC-DC for a faster charge.

Set the controller to AGM mode (option 2) - those voltages are a near-perfect match for TITAN lithium and will charge to 100%.

Basic DC to DC charger; charges to 100% when put on its lithium setting - typically fitted alongside a Truma SDC 12 MPPT solar controller.

Float-only voltage that protects lead-acid batteries from overcharging but only takes any battery to ~70-80% capacity. Ok to use if paired with solar that charges at 14.4V. Upgrade to a 14.4V mains charger to use the full TITAN capacity with mains only.

Not ideal. TITAN's higher resting voltage can keep the VSR latched open, causing a ~30W draw from the leisure battery back into the starter. Still ok to use, so long as user is aware of this discharge. Replace with a DC-DC charger for modern vehicles.

Behaves like the Durite VSR. It works, but while latched it lets the batteries balance between themselves, so a small drain sits on the lithium constantly. Fine to use if you are aware of the discharge; upgrading to a DC-DC charger is recommended.

Ships set for a 12.8V lithium nominal, but bulk-charges at 14.4V. Set absorption to 14.4V via the Bluetooth app - then it charges TITAN cleanly to 100%. Set absorbsion to 14.6V if cable length is long.

Recommended replacement for VSR / split charge relay setups on modern vehicles with smart alternators. Configurable, alternator-friendly and safe for TITAN's low internal resistance.

Charges TITAN at the correct voltage on AGM setting. Note small currents will take a long time to fully charge.

Compact 10A mains unit fitted to all Adria caravans and many older UK builds. 13.8V float-only voltage. Reaches ~70-80% on TITAN. Pair with a 14.4V solar or DC-DC charger - or upgrade the mains unit - to use the full TITAN capacity. Also replaces the older PS166-13.8-BCA variant. Worth confirming the exact part number on your install.

13.8V float-only voltage. Reaches ~70-80% on TITAN. Pair with a 14.4V solar or DC-DC charger - or upgrade the mains unit - to use the full TITAN capacity.

13.8V float-only voltage. Reaches ~70-80% on TITAN. Pair with a 14.4V solar or DC-DC charger - or upgrade the mains unit - to use the full TITAN capacity.

13.8V float-only voltage. Reaches ~70-80% on TITAN. Pair with a 14.4V solar or DC-DC charger - or upgrade the mains unit - to use the full TITAN capacity.

13.8V float-only voltage. Reaches ~70-80% on TITAN. Pair with a 14.4V solar or DC-DC charger - or upgrade the mains unit - to use the full TITAN capacity.

Dual-stage unit with a 2.5A boost output at 14.4V on the second leg. Charges TITAN to 100% as is - just slowly, due to the small boost current. Pair with a solar or DC-DC charger for a faster charge. Also replaces the older PS306-6A-BC. 2015 Elddis/Bailey conversions ship with an extra white lead from this unit - it isn't used by the charger, just tuck it away.

Dual-stage unit with a 2.5A boost output at 14.4V on the second leg. Charges TITAN to 100% as is - just slowly, due to the small boost current. Pair with a solar or DC-DC charger for a faster charge.

Dual-stage unit with a 2.5A boost output at 14.4V on the second leg. Charges TITAN to 100% as is - just slowly, due to the small boost current. Pair with a solar or DC-DC charger for a faster charge.

Dual-stage unit with a 2.5A boost output at 14.4V on the second leg. Charges TITAN to 100% as is - just slowly, due to the small boost current. Pair with a solar or DC-DC charger for a faster charge.

Set the DIP switches to Lithium (up/down/up/up) and it charges TITAN cleanly. Can be swapped for a Victron MPPT later if you want a slightly more efficient solar harvest.

Fitted under the driver's seat. Switch to the Lithium profile and it charges TITAN cleanly to 100%.

PWM controller - usable, but the 14.1V ceiling means it tops TITAN out at roughly 90-95%. Swap to an MPPT (Victron or Truma SDC) when you next refresh the solar side for a full charge.

Unscrew the front cover and set the internal DIP switch to mode B or C (14.4V bulk). The TITAN BMS protects against overshoot above 14.4V.

Charges TITAN at the correct 14.4V to a full 100%. Models and years covered vary - worth confirming the part number on the unit fitted in your install.

Charges TITAN at the correct 14.4V to a full 100%. Models and years covered vary - worth confirming the part number on the unit fitted in your install.

Charges TITAN at the correct 14.4V to a full 100%. Models and years covered vary - worth confirming the part number on the unit fitted in your install.

13.8V output only takes TITAN to ~80% on its own, but usually ships paired with a Truma SDC25 solar MPPT that finishes the charge to 100%. Worth confirming the Truma is fitted and on its Lithium profile (DIP up/down/up/up).